View M190EN04V2_9113478.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

c) copyright au optronics, inc. january, 2004 all rights reserved. m190en04 v.2 ver0.7 no reproduction and redistribution allowed. au optronics corporation product specifications 19.0 sxga color tft-lcd module model name: m190en04 v.2 approved by prepared by ccchiu ddbu marketing division / au optronics croporation customer checked & approved by spec. no.: ddpm-en04-1.0 version: 2 total pages: 30 date: 2004-july.05
c) copyright au optronics, inc. january, 2004 all rights reserved. m190en04 v.2 ver1.0 no reproduction and redistribution allowed. 1/30 product specifications 19.0 sxga color tft-lcd module model name: m190en04 v.2 ( ) preliminary specifications ( u ) final specifications note: this specification is subject to change without notice.
c) copyright au optronics, inc. january, 2004 all rights reserved. m190en04 v.2 ver1.0 no reproduction and redistribution allowed. 2/30 i contents ii record of revision 1.0 handling precautions 2.0 general description 2.1 display characteristics 2.2 functional block diagram 2.3 optical characteristics 2.4 pixel format image 3.0 electrical characteristics 3.1 absolute maximum ratings 3.2 connectors 3.3 signal pin 3.4 signal description 3.5 signal electrical characteristics 3.6 interface timing 3.6.1 timing characteristics 3.6.2 timing definition 3.7 power consumption 3.8 power on/off sequence 4.0 backlight characteristics 4.1 signal for lamp connector 4.2 parameter guideline for ccfl inverter 5.0 vibration, shock and drop 5.1 vibration and shock 5.2 drop test 6.0 environment 6.1 temperature and humidity 6.1.1 operating conditions 6.1.2 shipping conditions 6.2 atmospheric pressure 6.3 thermal shock 7.0 reliability 7.1 failure criteria 7.2 failure rate 7.2.1 usage
c) copyright au optronics, inc. january, 2004 all rights reserved. m190en04 v.2 ver1.0 no reproduction and redistribution allowed. 3/30 7.2.2 components de-rating 7.3 ccfl life 7.4 on/off cycle 8.0 safety 8.1 sharp edge requirement 8.2 material 8.2.1 toxicity 8.2.2 flammability 8.3 capacitors 9.0 other requirements 9.1 smoke free design 9.2 national test lab requirement 10.0 mechanical characteristics
c) copyright au optronics, inc. january, 2004 all rights reserved. m190en04 v.2 ver1.0 no reproduction and redistribution allowed. 4/30 ii record of revision version and date page old description new description remark 0.1 2004/02/06 all first edition for customer all 0.2 2004/3/19 9 definition of response time: white to black: rising time black to white: falling time definition of response time: black to white: riising time white to black: falling time modified 21 power on/off sequence : t1 min.= 0ms power on/off sequence : t1 min.= 0.5ms modified 28,29,30 mechanical drawings mechanical drawings modified 0.3 2004/03/09 20 vdd current: typ.1000ma max..1400ma vdd current: typ.1500ma max.1900ma modified 8 optical characteristics: na optical characteristics modified 7, 12 mating type part number: sm02(8.0)b-bhss mating type part number: sm02b-bhss-1-tb modified 0.4 2004/04/05 8 luminance uniformity :min.75% luminance uniformity:min.70% modified 8 luminance uniformity:typ.80% luminance uniformity:typ.75% modified 28,29,30 mechanical drawings mechanical drawings modified 0.5 2004/05/03 8 viewing angle, typ.(cr=10): r/l/u/d: 65/65/65/65 viewing angle, typ. (cr=10): r/l/u/d: 70/70/70/65 modified 8 viewing angle, min.(cr=10): r/l/u/d: 60/60/60/60 viewing angle, min. (cr=10): r/l/u/d: 65/65/65/60 modified 20 lcd inrush current: na lcd inrush current:.2.5a (max.) modified 0.6 2004/05/14 6 2.0 general description : 16m colors 2.0 general description : 262k colors modified 20 vdd power: typ.= 4.8w max. =7.5w vdd power: typ. =7.5w max. =10w modified 22 ccfl power consumption (max.): 25.8w ccfl power consumption (max.): 22w modified 1.1 2004/06/15 28,29,30 mechanical characteristics mechanical characteristics modified 10 viewing angle: cr=5 na viewing angle: cr=5 horizontal (right): >80 (left) : >80 vertical (up) : >80 (down): >80 modified
c) copyright au optronics, inc. january, 2004 all rights reserved. m190en04 v.2 ver1.0 no reproduction and redistribution allowed. 5/30 1.0 handling precautions 1) since front polarizer is easily damaged, please pay attention not to scratch it. 2) please be sure power supply is off, when inserting or disconnecting from input connector. 3) wipe off water drop immediately. long contact with water may cause discoloration or spots. 4) when the panel surface is soiled, wipe it with absorbent cotton or other soft cloth. 5) since the panel is made of glass, it may break or crack if dropped or bumped on hard surface. 6) since cmos lsi is used in this module, take care of static electricity and insure human earth when handling. 7) do not open nor modify the module assembly. 8) do not press the reflector sheet at the back of the module to any directions. 9) at the insertion or removal of the signal interface connector, be sure not to rotate nor tilt the interface connector of the tft-lcd module. 10) after installation of the tft-lcd module into an enclosure (lcd monitor housing, for example), do not twist nor bend the tft -lcd module even momentary. at designing the enclosure, it should be taken into consideration that no bending/twisting forces are applied to the tft -lcd module from outside. otherwise the tft -lcd module may be damaged.
c) copyright au optronics, inc. january, 2004 all rights reserved. m190en04 v.2 ver1.0 no reproduction and redistribution allowed. 6/30 2.0 general description this specification applies to the 19.0 inch color tft-lcd module m190en04.the display supports the sxga (1280 x 1024) screen format and 262k colors (rgb 6-bits). all input signals are 2 channel lvds interface compatible. this module does not contain an inverter card for backlight. 2.1 display characteristics the following items are characteristics summary on the table under 25 condition: items unit specifications screen diagonal [mm] 480 (19.0" ) active area [mm] 376.32 (h) x 301.056 (v) pixels h x v 1280(x3) x 1024 pixel pitch [mm] 0.294 (per one triad) x 0.294 pixel arrangement r.g.b. vertical stripe display mode normally white white luminance [cd/m 2 ] 250 (center, typ) @7ma contrast ratio 450 : 1 (typ) optical response time [msec] 16 ms(typ) color saturation 72% ntsc nominal input voltage vdd [volt] +5.0 v power consumption (vdd line + ccfl line) [watt] 28w(typ) (w/o inverter, all black pattern) weight [grams] 2700 (tbd) physical size [mm] 396 (h) x 324 (v) x 18 (d) (typ) electrical interface r/g/b data, clock support color 262k colors (rgb 6-bit data ) surface treatment anti-glare, hard coating, 3h temperature range operating storage (shipping) [ o c] [ o c] 0 to +50 -20 to +60 tco compliance meet tco 03 regulation
c) copyright au optronics, inc. january, 2004 all rights reserved. m190en04 v.2 ver1.0 no reproduction and redistribution allowed. 7/30 2.2 functional block diagram the following diagram shows the functional block of the 19.0 inches wide color tft-lcd module: jae fi-x30ssl-hf jst-bhsr-02vs-1 mating type: fi-x30hl sm02b-bhss-1-tb lvds receiver x - driver ic c o n n e c t o r dc/dc converter timing controller gamma correction tft-lcd 1280*(3)*1024 pixels g1 g1024 d1 d3840 inverter dc power 4 ccfl au asic rsds transmitter lvds + 5v 5v
c) copyright au optronics, inc. january, 2004 all rights reserved. m190en04 v.2 ver1.0 no reproduction and redistribution allowed. 8/30 2.3 optical characteristics the optical characteristics are measured under stable conditions at 25 (room temperature): item unit conditions min. typ. max. horizontal (right) cr = 10 (left) 65 65 70 70 - vertical (up) cr = 10 (down) 65 60 70 65 - horizontal (right) cr = 5 (left) >80 >80 viewing angle [degree] vertical (up) cr = 5 (down) >80 >80 contrast ratio normal direction 250 450 - raising time - 4 5 falling time - 12 20 response time (note 1) [msec] rising + falling - 16 25 red x 0.604 0.634 0.664 red y 0.324 0.354 0.384 green x 0.27 0.3 0.33 green y 0.585 0.615 0.645 blue x 0.108 0.138 0.168 color / chromaticity coordinates (cie) blue y 0.047 0.077 0.107 color coordinates (cie) white white x white y 0.28 0.30 0.31 0.33 0.34 0.36 white luminance @ ccfl 7ma (center) [cd/m 2 ] 200 250 - luminance uniformity (note 2) [%] 70 75 - cross talk (in 75hz) (note 3) [%] - - 1.5 equipment pattern generator, power supply, digital voltmeter, luminance meter (pr 880, bm-5a/ bm7) aperture 1 with 100cm vd or 2 with 50cm viewing distance test point center (vesa point 9) environment < 1 lux l c d m o d u l e pr-880 / bm5a / bm7 module driving equipment measuring distance
c) copyright au optronics, inc. january, 2004 all rights reserved. m190en04 v.2 ver1.0 no reproduction and redistribution allowed. 9/30 note 1: definition of response time the output signals of photo detector are measured when the input signals are changed from black to white (rising time), and from white to black (falling time), respectively. the response time is interval between the 10% and 90% of amplitudes. note 2: brightness uniformity of these 9 points is defined as below minimum luminance in 9 points (1-9) uniformity = maximum luminance in 9 points (1-9) 50 % 90 % 90 % 50 % 10 % 10 %
c) copyright au optronics, inc. january, 2004 all rights reserved. m190en04 v.2 ver1.0 no reproduction and redistribution allowed. 10/30 note 3: unit: percentage of dimension of display area l l a -l a l / l a x 100%= 1.5% max., l a and l b are brightness at location a and b l l b -l b l / l b x 100%= 1.5% max., l a and l b are brightness at location a and b 0 gray level 1/2 1/2 1/6 1/6 a b 1/2 1/2 1/6 1/6 2/3 1/3 1/3 2/3 a b 184 gray level 184 gray level
c) copyright au optronics, inc. january, 2004 all rights reserved. m190en04 v.2 ver1.0 no reproduction and redistribution allowed. 11/30 2.4. pixel format image following figure shows the relationship of the input signals and lcd pixel format. r g b r g b r g b r g b r g b r g b r g b r g b 1 2 1279 1280 1st line 1024 line 3.0 electrical characteristics 3.1 absolute maximum ratings absolute maximum ratings of the module is as following: item symbol min max unit conditions logic/lcd drive voltage vin -0.3 +5.5 [volt] select lvds data order sellvds nc nc [volt] ccfl inrush current icfll - 38 [ma] note 1 ccfl current icfl - 7.6 [ma] rms operating temperature top 0 +50 [ o c] note 2 operating humidity hop 8 95 [%rh] note 2 storage temperature tst -20 +60 [ o c] note 2 storage humidity hst 8 95 [%rh] note 2 note 1: duration=50 msec. note 2: maximum wet-bulb should be 39 and no condensation.
c) copyright au optronics, inc. january, 2004 all rights reserved. m190en04 v.2 ver1.0 no reproduction and redistribution allowed. 12/30 3.2 connectors physical interface is described as for the connector on module. these connectors are capable of accommodating the following signals and will be following components. connector name / designation interface connector / interface card manufacturer jae or compatible type part number fi-x30ssl-hf mating housing part number fi-x30hl connector name / designation lamp connector / backlight lamp manufacturer jst type part number bhsr-02vs-1 mating type part number sm02b-bhss-1-tb t=65 ,h=29% relative humidity % temperature - 20 0 60 50 95 5 100 0 operation range storage range storage range 80 60 40 20 twb=39 t=40 ,h=95% t=60 ,h=39% t=50 ,h=55% 65
c) copyright au optronics, inc. january, 2004 all rights reserved. m190en04 v.2 ver1.0 no reproduction and redistribution allowed. 13/30 3.3 signal pin pin# signal name pin# signal name 1 rxo0- 2 rxo0+ 3 rxo1- 4 rxo1+ 5 rxo2- 6 rxo2+ 7 gnd 8 rxoc- 9 rxoc+ 10 rxo3- 11 rxo3+ 12 rxe0- 13 rxe0+ 14 gnd 15 rxe1- 16 rxe1+ 17 gnd 18 rxe2- 19 rxe2+ 20 rxec- 21 rxec+ 22 rxe3- 23 rxe3+ 24 gnd 25 nc 26 nc 27 nc 28 power 29 power 30 power
c) copyright au optronics, inc. january, 2004 all rights reserved. m190en04 v.2 ver1.0 no reproduction and redistribution allowed. 14/30 3.4 signal description pin # signal name description 1 rxo0- negative lvds differential data input (odd data) 2 rxo0+ positive lvds differential data input (odd data) 3 rxo1- negative lvds differential data input (odd data) 4 rxo1+ positive lvds differential data input (odd data) 5 rxo2- negative lvds differential data input (odd data, h-sync,v-sync,dsptmg) 6 rxo2+ positive lvds differential data input (odd data, h-sync,v-sync,dsptmg) 7 gnd power ground 8 rxoc- negative lvds differential clock input (odd clock) 9 rxoc+ positive lvds differential clock input (odd clock) 10 rxo3- negative lvds differential data input (odd data) 11 rxo3+ positive lvds differential data input (odd data) 12 rxe0- negative lvds differential data input (even clock) 13 rxe0+ positive lvds differential data input (even data) 14 gnd power ground 15 rxe1- negative lvds differential data input (even data) 16 rxe1+ positive lvds differential data input (even data) 17 gnd power ground 18 rxe2- negative lvds differential data input (even data) 19 rxe2+ positive lvds differential data input (even data) 20 rxec- negative lvds differential clock input (even clock) 21 rxec+ positive lvds differential clock input (even clock) 22 rxe3- negative lvds differential data input (even data) 23 rxe3+ positive lvds differential data input (even data) 24 gnd power ground 25 nc - 26 nc - 27 nc - 28 power power 29 power power 30 power power note: input signals of odd and even clock shall be the same timing.
c) copyright au optronics, inc. january, 2004 all rights reserved. m190en04 v.2 ver1.0 no reproduction and redistribution allowed. 15/30 lvds data name description dsp display timing: (de mode) when the signal is high, the pixel data shall be valid to be displayed v-s vertical sync: both positive and negative polarity are acceptable h-s horizontal sync: both positive and negative polarity are acceptable ti lvds transmitter sn75lvds83 module lvds signal (interface connector pin7) signal name low(open) d0 red0 d1 red1 d2 red2 d3 red3 d4 red4 d5 red7 d6 red5 d7 green0 d8 green1 d9 green2 d10 green6 d11 green7 d12 green3 d13 green4 d14 green5 d15 blue0 d16 blue6 d17 blue7 d18 blue1 d19 blue2 d20 blue3 d21 blue4 d22 blue5 d23 na d24 h sync d25 v sync d26 display timing d27 red6
c) copyright au optronics, inc. january, 2004 all rights reserved. m190en04 v.2 ver1.0 no reproduction and redistribution allowed. 16/30 8bits input: m190en04 v2 only catch bit 2 to bit 7 for 6 bit display 6bits input data format marked with ( ). g0(0)r5(r3)r4(r2)r3(r1)r2(r0) r1(0)r0(0) rsv b7(b5)b6(b4)g7(g5)g6(g4) r7(r5)r6(r4) devshs b5(b3)b4(b2) b3(b1)b2(b0) b1(0)b0(0)g5(g3)g4(g2)g3(g1) g2(g0)g1(0) rclkp1 rap1 rbp1 rcp1 rdp1 g0(0)r5(r3)r4(r2)r3(r1)r2(r0) r1(0)r0(0) rsv b7(b5)b6(b4)g7(g5)g6(g4) r7(r5)r6(r4) b5(b3)b4(b2) b3(b1)b2(b0) b1(0)b0(0)g5(g3)g4(g2)g3(g1) g2(g0)g1(0) rclkp2 rap2 rbp2 rcp2 rdp2
c) copyright au optronics, inc. january, 2004 all rights reserved. m190en04 v.2 ver1.0 no reproduction and redistribution allowed. 17/30 note: r/g/b data 7:msb, r/g/b data 0:lsb 3.5 signal electrical characteristics input signals shall be low or hi-z state when vin is off it is recommended to refer the specifications of sn75lvds82dgg (texas instruments) in detail. each signal characteristics are as follows; parameter condition min max unit vth differential inputhigh voltage(vcm=+1.2v) 100 [mv] vtl differential input low voltage(vcm=+1.2v) -100 [mv] note: the value of vcm from lvds transmitter should follow the following guide. parameter min typ. max unit vcm +1.0 +1.2 +1.35 [v] 6 bits+ frc or 8 bits 0 1 2 3 4 5 8 bits lvds transmitter 0 1 2 3 4 5 6 7 8 bits lvds receiver 0 1 2 3 4 5 6 7 controller ic 8 bits rsds transmitter 6 bits rsds receiver driver ic scaling ic 01 23 45 67 01 23 45 open m190en04 module lvds interface system driver ic
c) copyright au optronics, inc. january, 2004 all rights reserved. m190en04 v.2 ver1.0 no reproduction and redistribution allowed. 18/30 3.6 interface timings 3.6.1 timing characteristics signal item symbol min typ max unit dtclk freq. fdck 50 67.5 70 mhz dtclk cycle tck 14.2 14.8 20 ns +v-sync frame rate 1/tv 56.25 75 77 hz +v-sync cycle tv 13 13.33 17.78 ms +v-sync cycle tv 1035 1066 2047 lines +v-sync active level tva 3 3 lines +v-sync v-back porch tvb 7 38 63 lines +v-sync v-front porch tvf 1 1 lines +dsptmg v-line m - 1024 - lines +h-sync scan rate 1/th - 80.06 - khz +h-sync cycle th 800 844 1023 tck +h-sync active level tha (*1) 4 56 tck +h-sync back porch thb (*1) 4 124 tck +h-sync front porch thf 4 24 tck +dsptmg display pixels n - 640 - tck note: typical value refer to vesa standard
c) copyright au optronics, inc. january, 2004 all rights reserved. m190en04 v.2 ver1.0 no reproduction and redistribution allowed. 19/30 3.6.2 timing definition 844dot 56 dot 124 dot 24 dot 640 dot h-sync dsptmg 42h 1h 38h 3h 1024h v-sync dsptmg
c) copyright au optronics, inc. january, 2004 all rights reserved. m190en04 v.2 ver1.0 no reproduction and redistribution allowed. 20/30 3.7 power consumption symbol parameter min typ max units condition vdd logic/lcd drive voltage 4.5 5 5.5 [volt] idd vdd current 1500 1900 [ma] vin=5v, all black pattern irush lcd inrush current - - 2.5 [a] note pdd vdd power 7.5 10 [watt] vin=5v, all black pattern vddrp allowable logic/lcd drive ripple voltage 100 [mv] p-p vddns allowable logic/lcd drive ripple noise 100 [mv] p-p note: measurement conditions: +5.0v +12.0v sw vcc r1 47k r2 1k vr1 47k f1 q3 ao6402 g d 2 s d 1 d 5 d 6 c1 1uf/16v q3 ao6402 g d2 s d1 d5 d6 c3 0.01uf/25v c2 1uf/25v (high to low) control signal (lcd module input) 90% 10% vin rising time 0 v 5. 0 v 470 us
c) copyright au optronics, inc. january, 2004 all rights reserved. m190en04 v.2 ver1.0 no reproduction and redistribution allowed. 21/30 3.8 power on/off sequence vin power and lamp on/off sequence is as follows. interface signals are also shown in the chart. signals from any system shall be hi-z state or low level when vin is off. 10% 90%90% 10% t1 t2t5t6t7 t3 t4 0v lamp signal vin10% 0v 0v 10% 90%90% 10% t1 t2t5t6t7 t3 t4 0v lamp signal vin10% 0v 0v 10% 90%90% 10% t1 t2t5t6t7 t3 t4 0v lamp signal vin10% 0v 0v values symbol min typ max unit t1 0.5 - 10 [ms] t2 0.5 40 50 [ms] t3 200 - - [ms] t4 200 - - [ms] t5 0.5 16 50 [ms] t6 0.5 - 10 [ms] t7 1000 - - [ms]
c) copyright au optronics, inc. january, 2004 all rights reserved. m190en04 v.2 ver1.0 no reproduction and redistribution allowed. 22/30 4.0 backlight characteristics 4.1 signal for lamp connector pin # signal name 1 lamp high voltage 2 lamp low voltage 4.2 parameter guideline for ccfl inverter symbol parameter min typ max units condition (l63) white luminance 200 250 - [cd/m 2 ] (ta=25 o c) iscfl ccfl standard current 6.5 7.0 7.5 [ma] rms (ta=25 o c) ircfl ccfl operation range 3.0 7.0 7.5 [ma] rms (ta=25 o c) icfl ccfl inrush current - 26 34 [ma] note 1 fcfl ccfl frequency 40 50 80 [khz] (ta=25 o c) note 2 vicfl (0 o c) ccfl ignition voltage 1800 [volt] rms (ta=0 o c) note 3 vicf (25 o c) ccfl ignition voltage 1500 [volt] rms (ta=25 o c) note 3 tcfl ccfl dark start time 1.0 sec (ta=25 o c) vcfl ccfl discharge voltage (reference) 700 @7.0ma 860 @6.5ma [volt] rms (ta=25 o c) note 4 pcfl ccfl power consumption 19.6 22 [watt] (ta=25 o c) note 4 note 1: duration=50 [msec] note 2: ccfl frequency should be carefully determined to avoid interference between inverter and tft lcd note 3: ccfl inverter should be able to give out a power that has a generating capacity of over 1800 voltage. lamp units need 1800 voltage minimum for ignition note 4: the variance of ccfl power consumption is 10%. calculator value for reference (icfl vcfl 4=pcfl). note 5: lamp connecting method is required to use terminal connecting .
c) copyright au optronics, inc. january, 2004 all rights reserved. m190en04 v.2 ver1.0 no reproduction and redistribution allowed. 23/30 5.0 vibrations, shock, and drop 5.1 vibration & shock frequency: 10 - 200hz sweep: 30 minutes each axis (x, y, z) acceleration: 1.5g (10~200hz p- p) test method: acceleration (g) 1.5 frequency (hz) 10~200~10 active time (min) 30 5.2 shock test spec: acceleration (g) 50 active time 20 wave form half-sin times 1 direction: x , y, z 5.3 drop test package test: the drop height is 60 cm.
c) copyright au optronics, inc. january, 2004 all rights reserved. m190en04 v.2 ver1.0 no reproduction and redistribution allowed. 24/30 6.0 environment the display module will meet the provision of this specification during operating condition or after storage or shipment condition specified below. operation at 10% beyond the specified range will not cause physical damage to the unit. 6.1 temperature and humidity 6.1.1 operating conditions the display module operates error free, when operated under the following conditions; temperature 0 0 c to 50 0 c relative humidity 8% to 95% wet bulb temperature 39.0 0 c 6.1.2 shipping conditions the display module operates error free, after the following conditions; temperature -20 0 c to 60 0 c relative humidity 8% to 95% wet bulb temperature 39.0 0 c 6.2 atmospheric pressure the display assembly is capable of being operated without affecting its operations over the pressure range as following specified; pressure note maximum pressure 1040hpa 0m = sea level minimum pressure 674hpa 3048m = 10.000 feet note: non-operation attitude limit of this display module = 30,000 feet. = 9145 m.
c) copyright au optronics, inc. january, 2004 all rights reserved. m190en04 v.2 ver1.0 no reproduction and redistribution allowed. 25/30 6.3 thermal shock the display module will not sustain damage after being subjected to 100 cycles of rapid temperature change. a cycle of rapid temperature change consists of varying the temperature from -20 0 c to 60 0 c, and back again. thermal shock cycle -20 0 c for 30min 60 0 c for 30min power is not applied during the test. after temperature cycling, the unit is placed in normal room ambient for at least 4 hours before powering on. 7.0 reliability this display module and the packaging of that will comply following standards. 7.1 failure criteria the display assembly will be considered as failing unit when it no longer meets any of the requirements stated in this specification. only as for maximum white luminance, following criteria is applicable. note : maximum white luminance shall be 115cd/m 2 or more . 7.2 failure rate the average failure rate of the display module (from first power-on cycle till 1,000 hours later) will not exceed 1.0%. the average failure rate of the display module from 1,000 hours until 16,000 hours will not exceed 0.7% per 1000 hours. 7.2.1 usage the assumed usage for the above criteria is: 220 power-on hours per month 500 power on/off cycles per month maximum brightness setting operation to be within office environment (25 0 c typical) 7.2.2 component de-rating all the components used in this device will be checked the load condition to meet the failure rate criteria.
c) copyright au optronics, inc. january, 2004 all rights reserved. m190en04 v.2 ver1.0 no reproduction and redistribution allowed. 26/30 7.3 ccfl life the assumed ccfl life will be longer than 40,000 hours, typical value is 50,000 hours under stable condition at 25 5 o c; standard current at 7.0 0.5ma. definition of life: brightness becomes 50% or less than the minimum luminance value of ccfl. 7.4 on/off cycle the display module will be capable of being operated over the following on/off cycles. on/off value cycles +vin and ccfl power 30,000 10 seconds on / 10 seconds off 8.0 safety 8.1 sharp edge requirements there will be no sharp edges or comers on the display assembly that could cause injury. 8.2 materials 8.2.1 toxicity there will be no carcinogenic materials used anywhere in the display module. if toxic materials are used, they will be reviewed and approved by the responsible au toxicologist. 8.2.2 flammability all components including electrical components that do not meet the flammability grade ul94-v1 in the module will complete the flammability rating exception approval process. the printed circuit board will be made from material rated 94-v1 or better. the actual ul flammability rating will be printed on the printed circuit board. 8.3 capacitors if any polarized capacitors are used in the display assembly, provisions will be made to keep them from being inserted backwards.
c) copyright au optronics, inc. january, 2004 all rights reserved. m190en04 v.2 ver1.0 no reproduction and redistribution allowed. 27/30 9.0 other requirements 9.1 national test lab requirement the display module will satisfy all requirements for compliance to ul 1950, first edition u.s.a. information technology equipment csa c22.2 no.950-m89 canada, information technology equipment eec 950 international, information technology equipment en 60 950 international, information processing equipment (european norm for iec950) 9.2 label 9.2.1 product label
c) copyright au optronics, inc. january, 2004 all rights reserved. m190en04 v.2 ver1.0 no reproduction and redistribution allowed. 28/30 10.0 mechanical characteristics
c) copyright au optronics, inc. january, 2004 all rights reserved. m190en04 v.2 ver1.0 no reproduction and redistribution allowed. 29/30
c) copyright au optronics, inc. january, 2004 all rights reserved. m190en04 v.2 ver1.0 no reproduction and redistribution allowed. 30/30

▲Up To Search▲

Price & Availability of M190EN04V2

	To Download M190EN04V2 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .